收藏本站
CAT24C32
BUS RELEASE DELAY (TRANSMITTER)
BUS RELEASE DELAY (RECEIVER)
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACK DELAY ( ≤ t AA )
Figure 4. Acknowledge Timing
ACK SETUP ( ≥ t SU:DAT )
SCL
t F
t LOW
t HIGH
t LOW
t R
t SU:STA
t HD:SDA
t HD:DAT
t SU:DAT
t SU:STO
SDA IN
t AA
t DH
t BUF
SDA OUT
Figure 5. Bus Timing
WRITE OPERATIONS
Byte Write
To write data to memory, the Master creates a START
condition on the bus and then broadcasts a Slave address
with the R/W bit set to ‘0’. The Master then sends two
address bytes and a data byte and concludes the session by
creating a STOP condition on the bus. The Slave responds
with ACK after every byte sent by the Master (Figure 6). The
STOP starts the internal Write cycle, and while this
operation is in progress (t WR ), the SDA output is tri ? stated
and the Slave does not acknowledge the Master (Figure 7).
Page Write
The Byte Write operation can be expanded to Page Write,
by sending more than one data byte to the Slave before
issuing the STOP condition (Figure 8). Up to 32 distinct data
bytes can be loaded into the internal Page Write Buffer
starting at the address provided by the Master. The page
address is latched, and as long as the Master keeps sending
data, the internal byte address is incremented up to the end
of page, where it then wraps around (within the page). New
data can therefore replace data loaded earlier. Following the
Acknowledge Polling
As soon (and as long) as internal Write is in progress, the
Slave will not acknowledge the Master. This feature enables
the Master to immediately follow ? up with a new Read or
Write request, rather than wait for the maximum specified
Write time (t WR ) to elapse. Upon receiving a NoACK
response from the Slave, the Master simply repeats the
request until the Slave responds with ACK.
Hardware Write Protection
With the WP pin held HIGH, the entire memory is
protected against Write operations. If the WP pin is left
floating or is grounded, it has no impact on the Write
operation. The state of the WP pin is strobed on the last
falling edge of SCL immediately preceding the 1 st data byte
(Figure 9). If the WP pin is HIGH during the strobe interval,
the Slave will not acknowledge the data byte and the Write
request will be rejected.
Delivery State
The CAT24C32 is shipped erased, i.e., all bytes are FFh.
STOP, data loaded during the Page Write session will be
written to memory in a single internal Write cycle (t WR ).
http://onsemi.com
6
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CAT24C512HU5IGT3 IC EEPROM SRL 512KB I2C 8UDFN
CAT24C512XI IC EEPROM I2C SRL 512KB 8SOIC
CAT24C64ZI-GT3 IC EEPROM I2C SRL 64KB 8MSOP
CAT24M01XI IC EEPROM I2C SRL 1MB 8SOIC
CAT24M01YI-GT3 IC EEPROM SRL 1MB I2C 8TSSOP
CAT25010LI-G IC EEPROM 1KBIT 10MHZ 8DIP
CAT25020VE-GT3 IC EEPROM 2KB I2C SER SPI 8SOIC
CAT25128XI IC EEPROM 128KB SPI SER 8SOIC
相关代理商/技术参数
CAT24C32VP2I-GT3 功能描述:电可擦除可编程只读存储器 32K-Bit I2C Serial RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C32WE-G 制造商:ON Semiconductor 功能描述:
CAT24C32WGI 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT24C32WGI-26751 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT24C32WGI-26756 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT24C32WGI-26758 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT24C32WGI-T3 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT24C32WI-G 功能描述:电可擦除可编程只读存储器 (4096x8) 32K 1.8-5.5 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8